GLOBAL SHEDS · SHED BUYER GUIDE

Will it fit? A practical guide to shed door sizes and access

What to measure before you order a machinery shed, workshop or garage

Illustration of a charcoal steel shed with a sloping awning over a roller door approach.

Illustration: a steel shed with a side awning over the approach. Not a customer project.

A tall roller door won’t help if your header can’t get under the awning on the way in. And a boat that fits through the opening on paper might still be impossible to reverse around a tight corner. Before you settle on a shed size, walk the route from the gate to where you’ll park. The tightest point along that route is the one that matters.

1. Measure what’s actually going in

Start with the biggest, widest and tallest things you need to get inside. They might be three different machines. Use their dimensions as they’ll really enter the shed, with the attachments and gear you normally leave on.

  • Height: measure to the highest fixed point in the configuration you’ll drive in. Think tractor cab, flashing light, roof rack, caravan air conditioner, or a boat on its trailer.
  • Width: include mirrors, tyres, guards, attachments and anything that sticks out at the sides.
  • Length: measure the whole setup you’ll be manoeuvring, including trailer drawbar and outboard where relevant. Leave room inside to get out, unhitch or work around it.

Think one purchase ahead. Taller tyres or a replacement trailer can raise the same boat or machine, even if the load hasn’t changed. For a first pass, add another 100 mm to the minimum height you think you need. That’s a planning buffer, not a guaranteed clearance: a sloping approach, a different trailer or how the rig sits can mean you need more. Tell us the measured height and the extra room you want, so both are clear on the drawing.

2. Ask for the clear opening, not just the door size

The number you want on the drawing is the usable width and height with the roller door fully open. Ask for the height from the finished floor to the lowest part of the opening, and the width between the closest obstructions. The door’s quoted size and the shed’s wall height are different numbers. Door guides, brackets and motors also need space, and the amount depends on the door and installation.

If two quotes look alike except for the price, check those dimensions side by side. A quote for a 3 m door isn’t comparable to one for a 4 m door if you need the extra height. Ask each supplier to show the actual clear opening on the drawing. There’s no single allowance that works for every vehicle and approach.

3. Check the lowest point under the awning

Say you’ve asked for a 4 m roller door. If the awning slopes down and the low point on your route is below the height you need, that door won’t solve the problem. A quote may list the awning’s eave height without showing what sits below it: a rafter, beam, gutter or header sheeting across the top of a bay that forms part of the bracing (sometimes called diaphragm bracing). Ask for the lowest usable clearance from the finished surface along your actual approach, including the outside edge of the awning, any framing or sheeting underneath, and the door itself.

Flag sloping driveways, a ramp up to the slab or changes in level. A trailer or long machine can sit at a different angle as it crosses the threshold. If room is tight, have the approach and levels checked before finalising the design.

Side view comparing the clear roller door opening with the lower clearance under an awning rafter or bracing.

Side view: the lowest obstruction on the way in can sit below the clear door opening. Illustrative, not to scale.

4. Make sure you can make the turn

We checked one backyard layout where the door was wide enough for the boat to pass through straight. The problem was a sharp left turn just before the opening. There wasn’t enough room for the boat and trailer to swing into line. We stopped and redesigned it before the customer committed.

Mark it out full size on the property with chalk, tape or cones. Lay out the shed walls, door opening, posts and shelving or workbench depth. Mark where the boat, car or machinery will sit. Then walk around it as you would on a normal day: open the car doors, picture unloading tools or getting a trolley past, and check you can still reach the shelving without squeezing between it and the gear.

Now mark the route from the gate or rear lane to the shed. On clear, safe ground, use cones to represent the door edges and practise reversing the boat or trailer into the proposed spot with a spotter. Mark the outside of the tow vehicle’s turn and where the rear of the trailer swings. That shows how much width you use to line up, not just how wide the trailer is. If you can’t trial it safely, sketch the swing lines and ask your designer or installer to check the path the whole rig needs.

Top-down sketch showing the door edges, reversing path, trailer swing, shelving and walkaround space.

Top view: mark the door edges, trailer swing, shelving and walking room. Illustrative, not to scale.

Two builds worth a look

Apple Tree Creek, QLD: A macadamia grower needed room for farm machinery and a car workshop. Jo worked through the size, door positions and clearances with him. The finished shed has four roller doors along one side. See the four-door shed.

Ivanhoe, VIC: On this 6 × 4 m single garage, a second look found the larger roller door was in the same price category. We could specify a 2.5 m high × 2.8 m wide door instead of 2.3 m × 2.6 m, without charging extra on that job. See the Ivanhoe garage.

What to send us before we quote

  • The full address where the shed will go. If there’s no street number yet, send the lot number and locality, or a map with the proposed position marked.
  • What you’ll use the shed for and the approximate height, width and length of the largest gear you need to get in.
  • A sketch or a few photos showing the gate, approach, slope and proposed door positions. Include any marked-out shelving and walkways, the trailer’s reversing path and swing lines, and any tight turns or overhead restrictions.

Rough gear measurements are fine to get the conversation started. Before you commit, we record the intended use and minimum clearances on our pre-contract checklist, then review those against the proposed design and engineering. We also check the site pin and approach for obvious access issues. Confirm final openings and levels from the approved drawings and with your installer before building.

Tell us what has to go through the door.